About this item:
1.12V voltage, 22MM handlebar inner diameter, suitable for most motorcycles.
2.The product is equipped with high and low gear switches, and the handle temperature can be adjusted at will (40℃-60℃ adjustable).
3.Double throttle cable buckle, wider installation range.
4.Can be sealed and can be ported design, does not affect the outside of the handle to install the handle to block, only the lights and other decorative accessories, more beautiful and more convenient.
5.IP67 waterproof level, even if the switch and handle cover are soaked in water, they can work normally. When the handle cover needs to be cleaned, only unplug the plug and wash with water, which is very convenient
6.Connection method: red connect to the positive pole, black connect to the negative pole
Product advantages:
【1】 The product adopts an integrated molding design to prevent rainwater and dust from entering and corroding the internal parts, resulting in a longer and safer service life
【2】 The product switch is equipped with an intelligent temperature control chip, which can adjust the temperature in three levels according to your own needs. Intelligent temperature control is safer
【3】 The product has an input voltage of 12V and a universal inner diameter of 22MM handle, suitable for most motorcycles
【4】 The product design adopts a dual throttle cable clip design, with a wider installation range
【5】 The product handle adopts a sealable and passable design, which does not affect the installation of decorative accessories such as handle plugs on the outside of the handle, making it more beautiful and convenient to use
【6】 The product has added a standby mode. After switching to standby mode, the electric heating handle will automatically maintain a constant temperature of around 50 degrees, which is more convenient for your use
【7】 The product line is equipped with a 5A fuse chip and a waterproof cover, which can automatically cut off the power when the car has problems, effectively preventing dangerous accidents from occurring
Operating instructions:
【1】 Power on: The red, blue, and green lights flash once each and then turn off
【2】 Standby: The red light flashes while breathing, and when the temperature reaches its maximum, it automatically switches to the blue light and enters the mid-range standby mode
【3】 Working status: indicator light is always on (high gear: red light is always on, medium gear: blue light is always on, low gear: green light is always on)
【4】 Long press the power button for 3 seconds: enter standby mode or shut down
【5】 Click on the key: Switch gears
Installation Instructions:
【1】 Firstly, remove the tools used by the original driver, and then clean the handlebars thoroughly
【2】 Then wet the inner holes of the left and right handles of the product with soapy water respectively, and install the left and right handles on the handlebars separately. During installation, the twisting amplitude should not be too large
【3】 When installing the right-handed handle, the power cord should have sufficient rotational margin to facilitate the rotation of the throttle and accelerator
【4】 Then fix the L bracket on the handle of this product to the position where the handle has screws, and secure the wire to the bracket to avoid shaking the handle wire back and forth and reduce damage
【5】 When connecting the power cord, connect the red wire of the product to the positive pole of the car power supply, and connect the black wire of the product to the negative pole of the car power supply. After confirming the positive and negative poles, do not connect them in reverse
【6】 Because this product's switch has two fixing methods (mirror fixing, 3M adhesive fixing), the aluminum alloy switch can be fixed to the iron bracket with small screws, and then the iron bracket can be fixed to the mirror base and tightened; Alternatively, you can directly apply 3m film to the back of the aluminum alloy switch, and then fix the 3m film in the appropriate position on the car
【7】 When installing the balance iron on the handle, adjust the position of the balance iron to be slightly separated from the handle. When tightening the screws, do not squeeze the handle. If the handle slides on the steel pipe during use, simply remove the balance iron and apply a few drops of 502 glue from the tail of the handle to fix it
Attention:
【1】 When installing the left handle, do not twist it too much, as excessive twisting can cause the heating wire to shift
【2】 For vehicles with balance iron, please adjust the installation position of the balance iron and do not squeeze the handle when tightening the screws. The balance iron should be slightly separated from the handle. If the installation position of the balance iron cannot be adjusted, please add a gasket between the balance iron and the handle to separate them. Over pressing the handle can cause difficulty in turning the handle switch, and abnormal damage such as electric heating wire extrusion on the surface of the handle
【3】 The above installation steps are only suitable for general vehicle models. For specific installation steps for special vehicle models, please install according to your own vehicle model
Product wiring method:
【1】 Connect the circuit of the motorcycle electric door lock (behind the key), with the red wire connected to the positive output wire of the electric door lock, and the black wire connected to any negative terminal or ground on the vehicle
【2】 Connect to the positive and negative terminals of the battery, with the red wire connected to the positive terminal [+] and the black wire connected to the negative terminal [-]
Reminder: When wiring, connect the red terminal to the positive terminal and the black terminal to the negative terminal. If connected in reverse, the switch will burn out, but the handle will heat up. Therefore, when wiring, please make sure to connect the positive and negative terminals before wiring to prevent burning out.
Specifications:
Product Name: Luxury Intelligent Three speed Temperature Regulating Electric Hand Handle (Aluminum Alloy Waterproof Switch)
Product Model: CSZH-983C1
Net weight of product: 301g
Product gross weight: 371g
Packaging method: Color box packaging
Packaging size: 11.4x6.4x19.6cm
Product Material: Nitrile material
Product Color: Black
Handle length: Left handle: 125mm; Right handlebar: 137mm
Input voltage: DC12V
Product power: Red light: 35W; Blue light: 25W; Green light: 17W
Working ring mirror temperature: -20 ° C -+50 ° C
Suitable handlebar diameter: 22mm
Handle type: sealable and passable electric handle
Switch type: Aluminum alloy multi-level adjustable temperature control switch
Switch fixing method: rearview mirror fixing, 3M adhesive fixing
Instructions for using the switch: Press and hold for 3 seconds to turn on the device. The red breathing light will turn on and enter standby mode. When the temperature reaches a certain level, it will automatically turn into blue mid-range; Lightly press to switch to blue light, the temperature is medium; Lightly press twice to turn green, indicating the lowest temperature; Press three times to turn red, indicating three levels of high temperature; Press and hold for 3 seconds to shut down
Applicable vehicle model: 12V motorcycle with a handle diameter of 22mm
Product accessories: 3M adhesive x1, rearview mirror fixing bracket x1, screws * 2
